t qp4m001 1 low loss sp 3t reflective switch datasheet: rev . c 0 5 - 0 1 - 1 4 - 1 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com applications ? wlan ? cellular infrastructure ? test and measurement ? smart energy ? uhf/vhf ? lmr ? general purpose broadband wireless product features ? general purpose ? broadband: 100 - 60 00 mhz ? low insertion loss: 0. 6 db a t 2 ghz ? high input ip3: + 55 dbm at 2 ghz ? cmos compatible triple voltage control ? lead free, rohs compliant qfn package functional block diagram 1 2 3 9 8 7 backside paddle - rf/dc gnd rf1 gnd v1 rf3 gnd v3 4 5 6 12 11 10 rf2 v2 gnd rfc n/c n/c pin 1 reference mark general description the TQP4M0011 is gaas fet single - pole, three throw (sp3t) switch with control signals from three independent control bias lines. signal path (switch) states m ay be controlled using dc voltages operating from 1.8 to 5 volts. the TQP4M0011 has 100 to 6000 mhz broadband performance the TQP4M0011 is packaged in a rohs - compliant, comp act 12 - pin 3x3 mm qfn package. the TQP4M0011 is an ideal choice for wireless infrastructure and test & measurement applications requiring low insertion loss and high input ip3 . it can also be used for any general purpose rf application where isolation is critical. 12- pin 3x3 mm qfn p ackage pin configuration pin no. symbol 1 v3 2 rf3 3, 4, 7 gnd 5 rf2 6 v2 8 rf1 9 v1 10, 12 n/c 11 rfc backside paddle rf/dc gnd ordering information part no. description TQP4M0011 sp 3 t reflective s witch TQP4M0011 - pcb 0.1 - 6.0 ghz evaluation board standard t/r size = 2500 pieces on a 7 reel topside view
t qp4m001 1 low loss sp 3t reflective switch datasheet: rev . c 0 5 - 0 1 - 1 4 - 2 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com electrical specifications test conditions unless otherwise noted: temp.=+ 25 c , 50 system parameter conditions min typ max units operational frequency range 100 6000 mhz control voltage low 0 0. 4 v high 1.8 3.3 5.0 v insertion loss 0.1 C 1.0 ghz 1.0 C 2.5 ghz 2.5 C 3.0 ghz 3.0 C 4.5 ghz 4.5 C 6.0 ghz 0. 4 0. 6 0. 8 1.2 1.5 db isolation 0.1 C 1.0 ghz 1.0 C 2.5 ghz 2.5 C 3.0 ghz 3.0 C 4.5 ghz 4.5 C 6.0 ghz 36 34 33 31 30 db return loss C rfc port 0.1 C 1.0 ghz 1.0 C 2.5 ghz 2.5 C 3.0 ghz 3.0 C 4.5 ghz 4.5 C 6.0 ghz 2 9 19 16 12 10 db input p1db f = 2 ghz +34 dbm input ip 3 f = 2 ghz , pout=+15 dbm/tone, f=1 mhz +55 dbm switching speed t on ,t off (50% ctl to 10/90% rf) 110 ns control voltage bias current v1 or v2 or v3 =5 v 15 ua recommended operating conditions parameter min typ m ax units v1/v2 /v3 high state 1.8 3.3 5.0 v operating temp. range - 40 +85 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating conditions. absolute maximum ratings parameter rating storage temperature - 6 5 to 150c rf input power , cw, 50, t = 25c +3 3 dbm control voltage ( v1/v2 /v3 ) + 6 v operation of this device outside the parameter ranges given above may cause permanent damage. switch control truth table control voltages signal path state v1 v1 v3 rfc to rf1 rfc to rf2 rfc to rf 3 low low high off (isolation) off (isolation) on (insertion loss) low high low off (isolation) on (insertion loss) off (isolation) high low low on (insertion loss) off (isolation) off (isolation) all other states n/a n/a n/a digital control voltages state bias condition low 0. 4 v high 1.8 v
t qp4m001 1 low loss sp 3t reflective switch datasheet: rev . c 0 5 - 0 1 - 1 4 - 3 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com performance plots - ( tqp4m00 11 - pcb) test conditions unless otherwise noted: temp= +25c, 50 system - 3.0 - 2.5 - 2.0 - 1.5 - 1.0 - 0.5 0.0 0 1 2 3 4 5 6 |s21| (db) frequency (ghz) rfc to rf1/2 insertion loss vs. freq. temp.=+25 - 40 - 30 - 20 - 10 0 0 1 2 3 4 5 6 |s11| (db) frequency (ghz) rfc port return loss vs. frequency temp.=+25 - 60 - 50 - 40 - 30 - 20 - 10 0 0 1 2 3 4 5 6 |s21| (db) frequency (ghz) rfc to rf1/2 isolation vs. freq. temp.=+25 reference design ( TQP4M0011 - pcb) j8 j5 j7 c4 c3 c2 c1 j5 j6 u1 j4 j1 j2 c7 c6 c5 j3 c3 100 pf j5 v1 j6 v2 j2 rf1 1 2 3 9 8 7 4 5 6 12 11 10 c2 100 pf j1 rfc c1 100 pf j3 rf2 j7 v3 j8 gnd c5 2.2 pf c6 2.2 pf c7 2.2 pf j4 rf3 c4 100 pf notes: 1. see evaluation board pcb specifications section for material and stackup. typical performan ce - ( TQP4M0011 - pcb) test conditions unless otherwise noted: temp= 25 c , 50 system parameter conditions typical value units frequency 1 2 3 g hz insertion loss rfc port to rf1 or rf2 or rf3 0.5 0.6 0.8 db rfc port return loss 2 9 25 16 db isolation rfc port to rf1 or rf2 or rf3 36 35 33 db input p1db +34 +34 +33.5 db m input ip3 pout= +15 dbm/tone, f=1 mhz +53 +55 +56 dbm
t qp4m001 1 low loss sp 3t reflective switch datasheet: rev . c 0 5 - 0 1 - 1 4 - 4 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com evaluation board pcb specifications pcb 109378 2 material and stack - up 1 oz. cu bottom layer nelco n-4000-13 core nelco n-4000-13 r =3.7 typ. 1 oz. cu top layer 1 oz. cu inner layer 1 oz. cu inner layer 0.014" 0.014" 0.062" 0.006" finished board thickness 5 0 ohm line dimension s: width = .02 8 , spacing = .0 28 pin configuration and description pin no. symbol description 1 v3 switch state control voltage 2 rf3 rf input/output port 3 3, 4, 7 gnd ground 5 rf2 rf input/output port 2 6 v2 switch state control voltage 8 rf1 rf input/output port 1 9 v1 switch state control voltage 10, 12 n/c no electrical connection. provide grounded land pads for pcb mounting integrity. 11 rfc antenna port backside paddle rf/dc gnd rf/dc ground. use recommended via pattern and en sure good solder attach for best thermal and electrical performance. t ops ide view
t qp4m001 1 low loss sp 3t reflective switch datasheet: rev . c 0 5 - 0 1 - 1 4 - 5 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com mechanical information package marking and dimensions marking: product code C xxxxx year/week - y yww assembly c ode - xxxxx top view side view bottom view 3.000.05 3.000.05 .20 ref. 0.000-0.050 pin #1 identification sq. 0.434 1.450.05 exp.dap 0.230.05 0.50 bsc 1.00 ref. 1.450.05 exp.dap 0.850.05 pin 1 locator gnd/thermal pad 0.400.05 n otes : 1. all dimensions are in millimeters . angles are in degrees. 2. dimension and tolerance formats conform to asme y14.4m - 1994. 3. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp- 012. pcb mounting pattern pin 1 locator component side 5x 3 12x 0.32 0.50 pitch 12x 12x 0.52 1.50 1.50 package outline 0.31 0.16 0.38 0.38 0.76 0.76 notes : 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. drill via holes as required for a final plated thru diameter of 0. 152 mm (0. 006 ). 4. ensure good package backside paddle solder attach for reliable operation a nd best electrical performance. xxxxx yyww xxxxx
t qp4m001 1 low loss sp 3t reflective switch datasheet: rev . c 0 5 - 0 1 - 1 4 - 6 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com produc t compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: class 1b (rf ports) value: ? 500 volts to < 1,000 volts esd rating: class 0 b (dc lines) value: ?125?v to < 250 volts test: human body model (hbm) standard: esda/ jedec standard js - 001- 2012 solderability comp atible with both lead - free (260 c max. reflow temperature) and tin/lea d (245 c max. reflow temperature) soldering processes. package contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipme nt). this product also has the following attributes: x lead free x halogen free (chlorine, bromine) x antimony free x tbbp - a (c 15 h 12 br 4 0 2 ) free x pfos free x svhc free msl rating msl rating : level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 important notice for the latest specifications, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@triquint.com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@triquint.com contact information the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or li ability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults , and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anyt hing described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause sev ere personal injury or death.
|
